HLM Folding Cleat, Marine Stainless Steel ,Deck-safe flush-folding cleat
$0.01HLM INDUSTRY Folding Cleat
Designed for deck safety, this cleat folds completely flat into its mounting base when not engaged, maintaining a low-profile surface that prevents accidental tripping
- Material:stainless steel
- Technique Procedure:Cast
- Finish: Polished
- High-Quality Stainless Steel: Built with corrosion-resistant stainless steel, making it suitable for marine and outdoor use.
HLM Formwork Cold Rolled Tie Rod, Diameter: D12mm/ D15mm/ D20mm | Ultimate Load: 70KN-260KN | For High-Tensile Strength and Dimensional Precision
$0.01HLM INDUSTRY Formwork Cold Rolled Tie Rod
Cold-rolled steel tie rods, available in materials like #45 or Q235 steel with various diameters, along with compatible accessories such as wing nuts, tie nuts, and formwork clamps, are designed for universal application in all types of concrete formwork and shuttering systems.
- Material: Q235, 45# Steel, Special mixture Steel
- Surface Treatment:Galvanized or as Nature
- Diameter: D12mm/ D15mm/ D20mm
- Ultimate Load: 70KN-260KN
- Weight:0.75kg/meter (D12mm) 1.50kg/meter (D15mm) 2.32kg/meter (D20mm)
- Related Products: Tie Nut, Wing Nut, Water Stop, Climbing Cone Nut, Hex Nut and etc.
HLM Formwork Hot Rolled Tie Rod, Diameter: DW15mm | Ultimate Load: 180KN-190KN | For Enhanced Ductility and Cost-Efficiency
$0.01HLM INDUSTRY Formwork Hot Rolled Tie Rod
A Formwork Hot Rolled Tie Rod is a discontinuously threaded rebar and a category of hot-rolled concrete tie rods.
- Material: Special mixture Steel
- Surface Treatment:Galvanized or as Nature
- Diameter: DW15mm
- Ultimate Load: 180KN-190KN
- Weight:1.42kg/meter
- Related Products: Tie Nut, Wing Nut, Water Stop, Climbing Cone Nut, Hex Nut and etc.
HLM Frame Turnbuckle with Eye&Eye, JIS Type | Stainless Steel | WT: 170-2750kg | Size: M5-M20
$0.01HLM INDUSTRY Frame Turnbuckle with Eye&Eye, JIS Type
SUS304/316L forged for balanced load transfer and vibration resistance in industrial plants.
- Material:Stainless Steel
- WT: 170-2750kg
- Size: M5-M20
- Standard:JIS Standard
- Finish:Polished
- High-Quality Stainless Steel: Built with corrosion-resistant 304/316 stainless steel, making it suitable for marine and outdoor use.
HLM Frame Turnbuckle with Eye&Hook, JIS Type | Stainless Steel | WT: 0.038-1.811kgs | Size: M5-M20
$0.01HLM INDUSTRY Frame Turnbuckle with Eye&Hook, JIS Type
SUS304/316L forged construction for permanent structural anchoring in industrial plants.
- Material:Stainless Steel
- WT: 0.038-1.811kgs
- WLL: 0.1-2.3 Tone
- Size: M5-M20
- Standard:JIS Standard
- Finish:Polished
- High-Quality Stainless Steel: Built with corrosion-resistant 304/316 stainless steel, making it suitable for marine and outdoor use.
HLM Frame Turnbuckle with Hook&Hook, JIS Type | Stainless Steel | WT: 40-900kg | Size: M5-M20
$0.01HLM INDUSTRY Frame Turnbuckle with Hook&Hook
SUS304/316L forged for balanced load transfer and vibration resistance in industrial plants.
- Material:Stainless Steel
- WT: 40-900kg
- Size: M5-M20
- Standard:JIS Standard
- Finish:Polished
- High-Quality Stainless Steel: Built with corrosion-resistant 304/316 stainless steel, making it suitable for marine and outdoor use.
HLM Full Aluminum Form Tie, Wall Thickness Size:6-12in | Safety Factor: 2:1 | Hole Diameter: 5/8 inch
$0.01HLM INDUSTRY Full Aluminum Form Ties
Precision-engineered for 6″ to 12″ wall thicknesses, featuring a 7,500 lb ultimate load capacity (3,600 lb SWL), universal aluminum formwork compatibility, and rebar stabilization, with clean break-off design for efficient stripping.
- End: Round
- Ultimate load: 7500 lbs
- Safe working load: 3600 lbs
- Safety Factor: 2:1
- Breakback: Standard
- Hole Diameter: 5/8 inch
- Performance Benefits:Uniform Stress Dispersion, Seamless System Integration for High-Volume Concrete Placement
HLM G-209/S-209 Carbon Screw Pin Anchor Shackle, 1/3t- 55t capacity｜Marine Grade｜Hot Dip Galvanized
$0.01HLM INDUSTRY G209/S209 Shackle
Capacities 1/3 thru 55 metric tons, grade 6.
Forged – Quenched and Tempered, with alloy pins.
Working Load Limit and grade “6″ permanently shown on every shackle.
Hot Dip galvanized or self colored.
Sizes 3/8 inch and below are mechanically galvanized.
Fatigue rated.
Shackles can be furnished proof tested with certification to designated standards, such as ABS, DNV, Lloyds, or other certification. Proof testing and certification available when requested at the time of order, charges will apply.
Approved for use at -40°C (-40°F) to 204°C (400°F).
All G-209/S-209 shackles meet Charpy V-notch impact requirements of 42 Joules (31 ft·lbf) avg. at -20°C (-4°F) upon special request.
Meets or exceeds all requirements of ASME B30.26.
Type Approval certification in accordance with ABS 2016 Steel Vessel Rules and ABS Guide for Certification of Lifting Appliances available. Certificates available when requested at time of order and may include additional charges.
HLM G-210/S-210 Round pin chain Shackle – Hot Dip Galvanized 5/16″ G-210 Screw Pin Chain Shackle – 3/4 Ton
$0.01HLM INDUSTRY G210/S210 Shackle
HLM G-213/S-213 Round pin Anchor Shackle, Galvanized, 3-1/4 Ton Working Load Limit, 5/8 inch Size
$0.01HLM INDUSTRY G213/S213 Shackle
- Forged, Quenched & Tempered, with alloy pins
- Working Load Limit permanently shown on every shackle
- Hot-dip galvanized
- Sizes 3/8″ and below are mechanically galvanized
- Fatigue rated to 20,000 cycles at 1-1/2 times the Working Load Limit
- Shackles can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds, or other certification; charges for proof testing and certification available when requested at the time of order
- Shackles are Quenched & Tempered and can meet DNV impact requirements of 42 Joules (31 ft-Ib) at -20° C (-4° F)
- G-213 Round pin anchor shackles meet the performance requirements of Federal Specification RR-C-271H, Type IVA, Grade A, Class 1, except for those provisions required of the contractor
HLM G-2130/S-2130 Bolt Type Anchor Shackle, Crosby 3/16″ Bolt Type Galvanized Safety Shackles for Secure Lifting & Rigging
$0.01HLM INDUSTRY G2130/S2130 Shackle
- Capacities 1/3 thru 150 metric tons, grade 6.
- Working Load Limit and grade “6” permanently shown on every shackle.
- Forged – Quenched and Tempered, with alloy pins.
- Hot Dip galvanized or Self Colored. (85, 120, and 150 metric ton shackles are all hot dip galvanized bows and the bolts are Dimetcoted® and painted red)
- Fatigue rated (1/3t – 55t).
- Shackles 25t and larger are RFID EQUIPPED.
- Approved for use at -40°C (-40°F) to 204°C (400°F).
- Meets or exceeds all requirements of ASME B30.26.
- Shackles 85 metric tons and larger are individually proof tested to 2.0 times the working load limit.
- Shackles 120 metric tons and larger are proof tested, Magnetic Particle Inspected and provided with Serialized Pin and Bow.
- Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.
- 3.1 Certification as standard available for charpy and statistical proof test only up to 25 tons to DNV2.7-1 and EN13889.
- Crosby 2t through 25t G2130 anchor shackles are type approved to DNV Certification Notes 2.7-1- Offshore Containers. These Crosby shackles are statistical proof and impact tested to 42 joules (31 ft.-lbs.) min. ave. at -20°C (-4°F). The tests are conducted by Crosby and 3.1 test certification is available upon request.
- All other 2130 and all 2150 shackles can meet chary requirements of 42 joules (31 ft.-lbs) avg. at -20°C (-4°F) upon special request.
HLM G-2130A bolt type Shackle , Crosby 7/8″ 5/8″ G-2130A Grade 8 Alloy Bolt Type Anchor Shackle 6-1/2 Ton WLL
$0.01HLM INDUSTRY G2130A Shackle
- Forged alloy steel, Quenched & Tempered, with bow and bolt
- Meets or exceeds all requirements of Grade 8 shackles
- Working Load Limit permanently shown on every shackle
- Hot-dip galvanized
- Meets or exceeds all requirements of ASME B30.26, including identification, ductility, design factor, proof load, and temperature requirements
- Importantly, G-2130A meet other critical performance requirements, including impact properties, and material traceability not addressed by ASME B30.26
- Shackles can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds, or other certification when requested at time of order (additional fees apply)
- Type Approval and certification in accordance with DNV 2.7-1 offshore containers
- Shackles are Quenched & Tempered and meet DNV impact requirements of 42 Joules (31 ft-Ib) at -40° C (-40° F)
- G-2130A Bolt Type Anchor shackles with thin head bolt – nut with cotter pin, meets the performance requirements of Federal Specification RR-C271H, Type IVA, Grade B, Class 3, except for those provisions required of the contractor