HLM JIS F2030-1978 SINGLE POINT MOORING PIPES(B), Weight:190-830kg | Bulwark Mounted Type | Cast Steel
$0.01HLM INDUSTRY JIS F2030-1978 SINGLE POINT MOORING PIPES(B)
Versatile Mounting – Type A/B options for different installation angles
Durable Construction – Heavy-duty cast steel for long-term reliability
Corrosion Protection – Sandblasting + dual-layer primer for enhanced rust prevention
Standardized Sizing – Multiple diameter options for various vessel requirements
HLM JIS Type Wire Rope Clip, Securing Wire Ropes | Size: 2-22 | AISI304/316L
$0.01HLM INDUSTRY JIS Type Wire Rope Clip
Premium Stainless Steel – Resists rust, corrosion, and wear
Secure Grip – U-bolt and saddle design ensures a tight, vibration-resistant hold
Smooth Surface – Polished finish minimizes rope damage
Easy Installation – Simple setup with standard tools
Versatile Use – Ideal for marine, construction, and industrial applications
HLM John Bracket, Heavy-Duty Snap Tie Brackets for Concrete Formwork | Wedge Adjustment Range: 5/8″
$0.01HLM INDUSTRY Snap Tie Bracket
A key component of the efficient Single Waler System, designed with 4-3/4″ L&W snap ties and a sliding wedge to accommodate lumber variations while enabling clean break-off with hex head ties for faster stripping.
- Material:Steel
- Finish: Body: Galvanized Wedge: Cadmium-Plated Steel
- Weight: 1.2 lbs.
- Wedge Adjustment Range: 5/8″
- Plywood Size(s): 3/4″, 5/8″
- Compatible With 4-3/4″ L&W Snap Ties
- Performance Benefits: Tri-axial force distribution, military-grade durability for critical formwork integrity
- John Bracket – Heavy-duty galvanized steel snap tie brackets with 5/8″ sliding wedge adjustment, compatible with 4-3/4″ L&W and hex head snap ties for versatile, weather-resistant single waler formwork systems.
HLM Jyt-Type High Holding Power Hall Anchor Marine Janpan Stock Anchors (HHP) TW Type Anchor Black painting, hot-dip galvanized
$0.01HLM INDUSTRY – JYT type high holding power anchor
TW type anchor is one kind of stockless high holding power anchor. The TW type HHP anchor has more than 2 times holding power than the conventional anchor of the same weight. The anchor has large flat flukes made out of high tensile steel plate material. The thickness varies from 15 mm up to 140 mm depending on the anchor size. It allows a weight reduction of 25% compared to a conventional anchor for the same equipment number It has a fully balanced type and unbalanced type. The fully balanced type always has its flukes in a vertical position while lifting the anchor. The unbalanced type will tip over to one side.
- HHP TW Type Anchor
- Weight: 20KG to 1000000KG
- Material: ZG230-45CH, Q345C, stainless steel 316L
- Finishing: Black painting, hot-dip galvanized
- Certificate: DNV-GL, BV, LRS, ABS, RINA, IRS, RS, CCS, KR, NK, etc
- Fully balanced or unbalanced anchor
- Customized design is available
HLM L-1327 Eye Sling Hook, 3200lb-90,400lb | Alloy Steel | G80/G100 Chain Compatible
$0.01HLM INDUSTRY L-1327 Eye Sling Hook
Forged Alloy Steel – Quenched and Tempered.
Each hook has a Product ldentification Code (PlC) for material traceabilit,along with the size and the name HLM.
25% stronger than Grade 80.
Eye Sling hooks incorporate two types of strategically placed markings forged into the product which address two (2)QUIC-CHECK® features: Deformation Indicators and Angle Indicators.
Low profile hook tip
Utilizes S-4320 integrated latch which meets the world standard for lifting.
Heavy duty stamped latch interlocks with the hook tip.
High cycle, long life spring.
When secured with the proper cotter pin through the hole in the tip of hook, meets the intent of OSHA Rule 1926.1431(g) and 1926.1501(g) for personnel lifting.
Individually Proof Tested to 2-1/2 times the Working Load Limit with certification
Suitable for use with Grade 100 and Grade 80 chain.
Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
“Look for the Platinum Color – HLM Grade 100 Alloy Products.”
HLM L-1338 Cradle Grab Hook ,4300lb-22,600lb Load | Alloy Steel | 2.5×WLL Proof Tested
$0.01HLM INDUSTRY L-1338 Cradle Grab Hook
Forged Alloy Steel – Quenched and Tempered.
Innovative cradle design allows for 100% efficiency of Grade 100 chain
Individually Proof Tested to 2-1/2 times the Working Load Limit with certification
Each hook has a Product ldentification Code (PlC) for material traceabilit , along with the size and the name HLM.
Suitable for use with Grade 100 and Grade 80 chain.
The use of A-1338 Cradle Grab Hook will allow 100 percent of the chain sling capacity.When used to hook back to chain leg to form a choker, the angle of the choke must be 120 degrees or greater. When used as a chain shortener, minimize twist of chain and ensure chain is fully engaged in hook.
Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
“Look for the Platinum Color – HLM Grade 100 Alloy Products.”
HLM L-1339 Clevis Sling Hook, 3200lb-44,100lb | Grade 80 & 100 Chain Approved | Alloy Steel
$0.01HLM INDUSTRY L-1339 Clevis Sling Hook
Forged Alloy Steel – Quenched and Tempered.
Individually Proof Tested to 2-1/2 times the Working Load Limit with certification
Each hook has a Product ldentification Code (PlC) for material traceabilit,along with the size and the name HLM.
Hoist hooks incorporate two types of strategically placed markings forged into the product which address two (2)QUIC-CHECK® features: Deformation Indicators and Angle Indicators.
Low profile hook tip
New integrated latch (S-4320/S-4339) meets the world standard for lifting.
Heavy duty stamped latch interlocks with the hook tip.
High cycle, long life spring.
When secured with the proper cotter pin through the hole in the tip of hook, meets the intent of OSHA Rule 1926.1431(g) and 1926.1501(g) for personnel lifting.
Suitable for use with Grade 100 and Grade 80 chain.
Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
“Look for the Platinum Color -HLMGrade 100 Alloy Products.”
HLM L-1358 Grab Hook, 4300lb-22,600lb Load | Rated 4:1 Safety Factor | Alloy Steel
$0.01HLM INDUSTRY L-1358 Grab Hook
Forged Alloy Steel – Quenched and Tempered.
Individually Proof Tested to 2-1/2 times the Working Load Limit with certification
Each hook has a Product ldentification Code (PlC) for material traceabilit , along with the size and the name HLM.
Suitable for use with Grade 100 and Grade 80 chain.
Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
“Look for the Platinum Color – HLM Grade 100 Alloy Products.”
HLM L-140 Standard Ratchet Type Load Binders with Hook and Pin Made from alloy Steel, then drop forged, machining, quenched & tempered.
$0.01HLM INDUSTRY – L-140 Ratchet Type Load Binder
Ratchet load binders 140 is a ratchet chain binder, this chain-tensioning device uses a ratcheting action to fast tighten chain to secure and tie down large loads, no need much strength like lever load binder to secure cargo.
Made from alloy Steel, then drop forged, machining, quenched & tempered.
- Upgraded for use with Grades 70, 80 and 100 Chain.
- Utilizes standard Crosby A-323 Alloy Eye Grab Hooks.
- New design “one piece” forged handle.
- Continuous take-up feature provides finite adjustment to tie down load.
- One piece assembly, no bolts or nuts to loosen.
HLM L-150 Snubbing Type Load Binders Suitable for binding steel, poles, lumber, pipes, or machinery
$0.01HLM INDUSTRY – L-150 Snubbing Type Load Binders
L-150 Snubbing Type Load Binders, used for safe and secure transportation of heavy loads.Made from forged steel that has been quenched and tempered. A spring cushion provides load protection from both shock and sway, while the binder toggles are kept away from the load.Typically used with low loader chains to tighten and pull chains together.Available in capacities up to 9,200lb and 1/2″ chain.
- Steel Coil Spring acts as a Shock Absorber bytaking up Chain Slack
- Great for rubber tired vehicle carriers
- Forged Hooks have 360° rotation
- Suitable for binding steel, poles, lumber, pipes, or machinery
HLM L-160 Heavy Duty Snatch Block with Hook , Hook Fitting | Sheave Diameter: 3-10in | WLL:2-12t
$0.01HLM INDUSTRY L-160 Heavy Duty Snatch Block with Hook
Constructed with reinforced forged steel and double-bearing side plates for extreme multidirectional load capacity in harsh mining and offshore operations.
- Opening feature permits easy insertion of rope without reeving, or while the block is suspended.
- Bolt for opening feature is retained, to ensure no lost bolts.
- Forged steel swivel tees, yokes and hooks.
- Furnished with a latch installed.
- Can be furnished with bronze bushings or roller bearings.
- Center pin equipped with pressure lube fitting.
- All sizes feature sheave grooves suited for a range of wire line diameters.
- Meets or exceeds all requirements of ASME B30.26 including identification ductility, design factor, proof load and temperature requirements.
Importantly, these blocks meet other critical performance requirements including fatigue life and material traceability,not addressed by ASME B30.26.
- “All Alloy” snatch blocks feature a significant reduction in weight compared to snatch blocks made of non-alloy materials.
- “Lebus General Purpose” snatch blocks (with shackle or hook) feature an easy-to-open bolt design. The retaining bolt is released by rottating the fitting assembl , no tools required.
- HLM’s Engineered Solutions Group is ready to discuss your requirements and help select or develop the ideal block for your application.
HLM L-170 General Purpose Snatch Block with Hook, Hook Fitting | Single Sheave | WLL:2-12t
$0.01HLM INDUSTRY L-170 General Purpose Snatch Block with Hook
A multi-functional hoisting device designed for construction, rigging, and load movement applications, equipped with a 105mm diameter pulley, forged steel hook, and compatible with both wire and fiber ropes.
- Opening feature permits easy insertion of rope without reeving, or while the block is suspended.
- Bolt for opening feature is retained, to ensure no lost bolts.
- Forged steel swivel tees, yokes and hooks.
- Furnished with a latch installed.
- Can be furnished with bronze bushings or roller bearings.
- Center pin equipped with pressure lube fitting.
- All sizes feature sheave grooves suited for a range of wire line diameters.
- Meets or exceeds all requirements of ASME B30.26 including identification ductility, design factor, proof load and temperature requirements.
Importantly, these blocks meet other critical performance requirements including fatigue life and material traceability,not addressed by ASME B30.26.
- “All Alloy” snatch blocks feature a significant reduction in weight compared to snatch blocks made of non-alloy materials.
- “Lebus General Purpose” snatch blocks (with shackle or hook) feature an easy-to-open bolt design. The retaining bolt is released by rottating the fitting assembl , no tools required.
- HLM’s Engineered Solutions Group is ready to discuss your requirements and help select or develop the ideal block for your application.